Choose your Automotive paint color for your 2012 Subaru Tribeca

Restore Your Subaru Finish In Two Steps

Select Your Subaru's Color (Step One)

AutomotiveTouchup paint products are custom mixed to perfectly match the color of your 2012 Subaru Tribeca using a basecoat/clearcoat system just like factory specs. To insure a proper match, you’ll need to know your vehicle’s color code so you can find it on the chart below. Click here for Subaru paint code location diagrams and label examples.

Chip Color Codes Color Description
2012 Subaru Tribeca Touch Up Paint | Crystal Black Silica Pearl D4S, EH3 D4S, EH3 Crystal Black Silica Pearl
2012 Subaru Tribeca Touch Up Paint | Graphite Gray Metallic EH4, F3T EH4, F3T Graphite Gray Metallic
2012 Subaru Tribeca Touch Up Paint | Caramel Bronze Pearl F1H F1H Caramel Bronze Pearl
2012 Subaru Tribeca Touch Up Paint | Ice Silver Metallic G1U, GE2 G1U, GE2 Ice Silver Metallic
2012 Subaru Tribeca Touch Up Paint | Deep Indigo Pearl G5U, GE8 G5U, GE8 Deep Indigo Pearl
2012 Subaru Tribeca Touch Up Paint | Venetian Red Pearl H2Q, HZ9 H2Q, HZ9 Venetian Red Pearl

 

Don't see your color listed?


Call 1-888-710-5192.
We probably have it.

Did you choose the wrong vehicle model?


Did you choose the wrong model? How about the 2012 Subaru BRZ, Forester, Impreza, Legacy, Outback, or WRX?  If you're still not sure, take a look at our All 2012 Subaru Models page.  Or, just go to our page dedicated to Subaru Touch Up Paint

Why The Two-Step Paint System?

Your 2012 Subaru Tribeca is painted at the factory with a high quality basecoat/clearcoat system. This two-step paint system consists of step one, the basecoat, which is your car’s actual color, and step two, the clearcoat, the specially formulated clear paint that protects the base color and provides the luster and deep shine your vehicle came with when new. AutomotiveTouchup products faithfully reproduce your vehicle manufacturer’s basecoat/clearcoat system.

Here's what our customers are saying about our Touch Up Paint:

Bud Keene, owner of a 2011 Subaru Forester from Union Hall, VA

I painted a panel of my 2011 Subaru which was a Green Gray Metallic/Sage Green Metallic C1F. The results perfectly matched the rest of the car. First I painted a piece of scrap metal, compared it to my car and it looked totally different. Then my wife commented that the perceived color depends on the orientation of the piece. The color goes from green to gray depending on the lighting and the the slant of the section. Sure enough when I positioned the test piece in exactly the same direction as a straight car section (a vertical area on the back of the car) it was an exact match. The car panel had several scratches down to the original primer with rough edges of color around the scratches. Here's how i did it. 1. I smoothed out the scratches down to the primer with 320 wet/dry sandpaper, and then lightly scuffed the rest of the panel to remove gloss. If I were to do it again, I would use a slightly finer paper to scuff the undamaged area. 2. I masked the adjacent panels and the windshield using quality masking tape and plastic sheeting. the sheeting covered wide areas to be sure that my spraying would not hit any of the other areas. 3. I applied 3 light coats of the color waiting 30 minutes between the coats. Be careful not to overspray which could cause sags, and don't touch a prominent areas to check if it's dry. If not dry it will leave a mark. 4. After one hour I lightly sanded the final color coat with 2000 wet/dry paper which I found at my auto store. 5. I then applied 3 coats of the clear coat, again waiting 30 minutes between coats. The refinished area totally matched color of the adjoining panels. The job was done in one afternoon, and most of the time was spent watching TV between coats. 3. I sprayed the damaged panel with the color coat, applying 3 coats....waiting 30 minutes between coats. I used very light coats to be sure that it would not sag. NOTE: After spraying a coat, turn the can upside down and press the nozzle until just propellent comes out. Otherwise the nozzle may clog with dried paint. My only suggestion is that you provide similar application directions with the paint.

Jerry E, owner of a 2011 Subaru Forester from PA

The paint matched my vehicle exactly. Great product, good communication, and fast service. Saved beaucoup $$ rather than having a body shop do the painting. Would definitely buy from AutomotiveTouchup again.

Share your touch up story...